Model Ship Builder :: Forums :: Build Logs :: POF Build Logs |
|
<< Previous thread | Next thread >> |
William Carson 1846 barque (1:48) |
Go to page 1 2 3 4 5 | |
Moderators: Winston, aew, bikepunk
|
Author | Post | ||
ToddM |
| ||
![]() Registered Member #4538 Joined: Wed Dec 10 2014, 05:47pmPosts: 231 | Using scotch tape I determined the curve of the deck shelves (no deck clamps will be used). ![]() this was mirrored for the port side ![]() ![]() ![]() ![]() | ||
Back to top | | ||
ToddM |
| ||
![]() Registered Member #4538 Joined: Wed Dec 10 2014, 05:47pmPosts: 231 | I clamped the frames so that they would remain flush on the outside to facilitate the installation of planks![]() The process was repeated for the main deck shelf ![]() ![]() ![]() | ||
Back to top | | ||
ToddM |
| ||
![]() Registered Member #4538 Joined: Wed Dec 10 2014, 05:47pmPosts: 231 | The knees for the beams were cut and the ones towards the bow and stern were beveled. It was easier to notch the shelves than the knees when putting in place.![]() ![]() ![]() ![]() ![]() ![]() | ||
Back to top | | ||
ToddM |
| ||
![]() Registered Member #4538 Joined: Wed Dec 10 2014, 05:47pmPosts: 231 | The beams were then cut and notched and glued in place. the carlings were then cut to fit and glued. Pillars were added between the keelson and deck beams.![]() ![]() ![]() ![]() ![]() ![]() The accommodation deck beams completed. Not sure yet whether or not to add deck planking to this deck or not. I have to determine how I want to finish this ship as far as showing the construction. I may just plank half of the main deck and completely plank the outside of one side of the ship. ![]() ![]() | ||
Back to top | | ||
aew |
| ||
aew![]() ![]() ![]() Registered Member #1929 Joined: Wed Nov 30 2011, 03:05pmPosts: 2618 | Well I can see why you don't want to cover up the construction! | ||
Back to top | | ||
jacknastyface2 |
| ||
![]() Registered Member #5239 Joined: Sat Apr 21 2018, 05:29pmPosts: 148 | My, you have been busy! Looking good. Keith. | ||
Back to top | | ||
Tim C |
| ||
![]() ![]() Registered Member #4126 Joined: Fri Feb 15 2013, 05:19amPosts: 1007 | Outstanding. Someday I hope to make something as nice as that. Way to go!! Later Tim | ||
Back to top | | ||
Charles |
| ||
![]() ![]() Registered Member #1923 Joined: Mon Nov 28 2011, 06:07pmPosts: 506 | Do not know what to said Just …….. so good | ||
Back to top | | ||
ToddM |
| ||
![]() Registered Member #4538 Joined: Wed Dec 10 2014, 05:47pmPosts: 231 | Thanks for the positive notes!! I get away from reading on this forum, but when I return it is nice to see these notes as well as peek at what else is being done on this site. It is fantastic what is being planned and built. It is all very encouraging to know that this is something that I can do for many years. I wish I had started to do this back when my back and eyes were in much better shape! Todd | ||
Back to top | | ||
jacknastyface2 |
| ||
![]() Registered Member #5239 Joined: Sat Apr 21 2018, 05:29pmPosts: 148 | ToddM wrote ... Thanks for the positive notes!! I get away from reading on this forum, but when I return it is nice to see these notes as well as peek at what else is being done on this site. It is fantastic what is being planned and built. It is all very encouraging to know that this is something that I can do for many years. I wish I had started to do this back when my back and eyes were in much better shape! Todd I know the feeling well! I have almost given up doing any more modeling because of physical problems. I need more light in the workshop, have to sit, not stand because of balance and back trouble, and altogether am dissatisfied with the very little I do. Tch! "golden years"?? I don't think so. Please keep on with the William Carson. Splendid job. Keith | ||
Back to top | | ||
Go to page 1 2 3 4 5 | |
Powered by e107 Forum System